Introduction In food and drink production, clean floors are not just about appearance. They are part of keeping n products safe, passing audits and p rotecting staff from slips. Production areas deal with water, fats, sugars, flour, spills and constant foot traffic, often across long shifts with little downtime for cleaning. That makes the choice of cleaning equipment important. The right machines clean more thoroughly, more consistently and in less time than manual methods. This guide looks at the main challenges and the equipment that helps. The challenges of food production floors Every site is different, but most share a few common problems: • Wet floors from washdowns, spills and processes, which create a slip risk. • Fats, oils and grease that make floors slippery and are hard to remove with water alone. • Dry residues such as flour, sugar and crumbs that spread quickly if not cleared. • Limited time between production runs or shifts. • High standards set by customers, auditors and food safety requirements. Why mops fall short Mops and buckets are still common in many food sites, but they have limitations. The water quickly becomes dirty, so the mop can spread contamination rather than remove it. Floors are left wet , which increases slip risk and slows down the return to production. Results also vary from person to person and shift to shift. Scrubber dryers for consistent results A scrubber dryer applies clean solution, scrubs the floor and removes the dirty water in a single pass. That means: • dirty water is taken away rather than spread around • floors are left dry and safe much sooner • cleaning is consistent across every shift • staff spend less time and effort on each clean Compact machines such as the Tennant T360 suit processing rooms and areas around equipment, while larger walk-behind and ride-on machines cover packing halls , warehouses and dispatch areas. Steam cleaning for equipment and hard-to-reach areas Steam cleaners, such as the Matrix range , use high-temperature steam to loosen dirt and grease from equipment, surfaces, drains and hard-to-reach areas. They use very little water, so they are useful where you want to avoid soaking an area. Steam is also effective on tiles, grout and stainless steel. Hot water pressure washers without fumes Hot water cuts through fats and grease far faster than cold water. In food production, all-electric hot water pressure washers such as the Dirt Driver Electrifire range are particularly useful, as they produce no exhaust fumes and can be used in enclosed areas. They are suited to washing down equipment, floors, drains and external areas such as yards and bin stores. Wet and dry vacuums for spills Large spills and standing water need to be removed quickly. Heavy-duty wet and dry vacuums, such as the Numatic WVD1800AP , lift liquids fast so the area can be cleaned and back in use sooner. Chemical-free cleaning options Some food businesses want to reduce the number of chemicals they store and handle. Systems such as Tersano produce a cleaning and sanitising solution on site from tap water, which can reduce the need to buy, store and mix traditional chemicals. Always check that any cleaning method meets your own food safety procedures. Building the right cleaning set-up Most food production sites use a combination of equipment rather than a single machine. A typical set-up might include a scrubber dryer for floors, a steam cleaner for equipment and detail cleaning, a hot water pressure washer for washdowns and a wet and dry vacuum for spills . The right mix depends on your products, processes and layout. Support from a local specialist Cornwall Vacuum Services supplies, leases, services and repairs cleaning equipment for food and drink producers across Cornwall, Devon, Somerset and Dorset. We can visit your site, look at your floors, processes and cleaning routine, and recommend equipment that helps you meet your standards. Contact our team to arrange a consultation. FAQs What is the best way to clean food production floors? A scrubber dryer is usually the most effective method, as it scrubs the floor and removes dirty water in one pass, leaving the floor clean and dry. Can pressure washers be used indoors in food production areas? All-electric hot water pressure washers produce no exhaust fumes, which makes them suitable for many indoor areas. Always follow your site's own procedures. Are steam cleaners suitable for food production? Steam cleaners are useful for cleaning equipment, surfaces and hard-to-reach areas with very little water. Check that the method fits your food safety procedures. How can we reduce slip risk in wet production areas? Removing water quickly is key. Scrubber dryers leave floors dry after cleaning, and wet and dry vacuums remove spills and standing water fast.  Can we reduce the chemicals we use for cleaning? Chemical-free systems such as Tersano can reduce the need to buy and store some traditional cleaning chemicals.

Holiday Park Cleaning - Introduction On a busy holiday park, changeover day is a race against the clock. Guests leave in the morning, new arrivals are due in the afternoon, and every lodge, caravan and cabin has to be cleaned, checked and ready in between. Add shower blocks, clubhouses, pools, site roads and car parks, and it is easy to see why cleaning teams feel the pressure in peak season. The right equipment can make a real difference. It helps teams work faster, clean more consistently and leave every accommodation ready for the next guests. This guide looks at the areas that matter most and the machines that help. Inside lodges and caravans Accommodation is where guests notice cleanliness first. Carpets, rugs, hard floors and soft furnishings all need attention at every changeover. • Backpack vacuums, such as the Pacvac range , let cleaners move quickly from room to room without dragging a cylinder behind them. They are ideal for compact spaces such as caravans, lodges and glamping units, and they reach stairs, under beds and into corners easily. • Carpet extractors, such as the Prochem range , deep clean carpets and upholstery between stays , removing stains and freshening fabrics. They are especially useful at the end of the season or after a messy stay. • Compact scrubber dryers , such as the i-mop range , clean kitchen and bathroom floors and leave them dry, so they are ready to walk on straight away. Shower blocks, pools and leisure areas Shared facilities get heavy use and need to stay clean and safe throughout the day. Wet floors in shower blocks, changing rooms and around pools are a slip risk , so cleaning them quickly and leaving them dry is important. Compact scrubber dryers clean and dry these floors in one pass, rather than leaving them wet as a mop would. Steam cleaners can also help with tiles, grout and fittings in washrooms. Clubhouses, bars and entertainment venues Clubhouses and entertainment areas often combine carpeted lounges, hard-floored bars and busy entrances . A mix of commercial vacuums, carpet cleaning machines and a compact scrubber dryer keeps these spaces presentable from opening until close, and ready again for the next day. Site roads, car parks and outdoor areas The outside of the park makes the first impression on arrival. Site roads, car parks and paths collect leaves, grit and litter, especially in busy periods. • Ride-on sweepers, such as the Tennant S20 , clear site roads and car parks quickly and keep them tidy for arriving guests. • Pressure washers clean decking, patios, bin stores and outdoor furniture. Petrol models such as the Evolution 1 work in areas without mains power. • Flat surface cleaners , such as the Turbo Devil TD520, attach to a pressure washer and clean decking, paths and patios more evenly than a standard lance. Gutters and high-level cleaning Gutters on lodges, clubhouses and reception buildings fill with leaves and moss, especially on parks surrounded by trees. A high-level vacuum such as the skyVac Industrial 85 clears gutters from the ground, without ladders or scaffolding, which makes it practical to keep on top of them through the year. Planning for peak season The worst time for a machine to break down is the middle of the summer holidays. Booking servicing before the season starts helps make sure vacuums, carpet cleaners, scrubber dryers and pressure washers are ready for the busiest weeks. It is also a good time to review whether your team has the right equipment for the number of units on site. Equipment and support for holiday parks Cornwall Vacuum Services supplies, leases, services and repairs commercial cleaning equipment for holiday and leisure parks across Cornwall, Devon, Somerset and Dorset. We can look at your park, your changeover routine and your facilities, and recommend equipment that helps your team work faster. Contact us to arrange a consultation. FAQs What is the best vacuum for cleaning caravans and lodges? Backpack vacuums are popular for holiday accommodation because they are lightweight, quick to use and easy to carry between units and up stairs. How can we speed up changeover cleaning? Using equipment suited to each task, such as backpack vacuums for accommodation and compact scrubber dryers for kitchens and bathrooms, helps teams clean faster and more consistently. What equipment do we need for site roads and car parks? A sweeper keeps roads and car parks clear of debris, while a pressure washer with a flat surface cleaner handles decking, paths and patios. Can gutters be cleaned without ladders? Yes. High-level vacuum systems clear gutters from the ground, reducing the need for ladders or scaffolding. When should we service our cleaning equipment? Before the start of the busy season is ideal, so machines are ready for peak changeovers.

How to clean a warehouse A clean warehouse is safer, more efficien t and better for stock , equipment and staff. But with large floors, high racking, constant vehicle movement and tight shift patterns, it is easy for cleaning to become reactive, done only when something looks bad or after a spill. A simple cleaning schedule solves that. By breaking jobs into daily, weekly, monthly and quarterly tasks, you can keep the whole building under control without disrupting operations. Here is a practical schedule you can adapt for your site, along with the equipment that makes each job easier. Daily tasks Daily cleaning focuses on safety and the areas that get dirty fastest. • Sweep traffic lanes and loading areas to remove dust, grit and packaging debris. A ride-on sweeper such as the Tennant S20 covers large areas quickly. • Deal with spills straight away . A wet and dry vacuum such as the Numatic WV1800DH lifts liquids fast, reducing slip risk. • Empty bins and clear packaging waste before it spreads across the floor. • Check walkways and fire exits are clear of debris and obstructions. Weekly tasks Weekly cleaning tackles the dirt that sweeping leaves behind. • Scrub busy traffic lanes and turning areas to remove tyre marks and ingrained dirt. A ride-on scrubber dryer such as the Tennant T20 washes and dries large floors in a single pass. • Clean loading bays and dock areas, where dirt from outside is tracked in. • Clean welfare areas, canteens and toilets thoroughly. • Check cleaning machines, including brushes, squeegees and filters, so they are ready for the week ahead. Monthly tasks Monthly cleaning reaches the areas that are easy to forget. • Scrub the full warehouse floor , including quieter aisles and storage areas. • Clean beneath and around racking where dust and debris collect. • Remove dust from high-level areas , such as racking tops, beams and ledges. Dust that builds up overhead can fall onto stock and staff. • Clean doors, frames and dock levellers. Quarterly tasks Every few months, plan a deeper clean. • Deep clean the whole floor, using a more aggressive brush or pad on heavily marked areas. • Clear gutters and high-level drainage. A high-level vacuum such as the skyVac Industrial 85 clears gutters from the ground, without the cost of scaffolding. • Pressure wash yards, external walkways and bin areas. • Book planned servicing for your cleaning machines so they stay reliable. Making the schedule work A schedule only works if it fits around your operation. A few tips: • Clean in quieter periods, such as between shifts or at the start of the day. • Assign clear responsibilities so each task has an owner. • Use the right machine for each job. Sweepers for loose debris, scrubber dryers for ingrained dirt and wet and dry vacuums for spills. • Keep a simple checklist so tasks are ticked off and nothing is missed. • Review it regularly. Busy periods, new layouts or more vehicle traffic may mean some tasks need doing more often. Equipment to support your schedule The right equipment makes a warehouse cleaning schedule far easier to stick to. Cornwall Vacuum Services supplies, leases, services and repairs industrial sweepers, scrubber dryers, wet and dry vacuums and high-level cleaning equipment for warehouses across Cornwall, Devon, Somerset and Dorset. We can look at your site and recommend the machines that will make the biggest difference . Contact our team to arrange a site visit. FAQs How often should a warehouse be cleaned? Busy areas need daily attention, especially traffic lanes, loading bays and spills. A full floor scrub is usually done weekly or monthly, with a deeper clean every few months. What equipment do I need to clean a warehouse? Most warehouses benefit from a sweeper for loose debris, a scrubber dryer for ingrained dirt and marks, and a wet and dry vacuum for spills. High-level cleaning equipment helps with racking and gutters. How do I clean high-level areas in a warehouse? High-level vacuum systems with extendable poles can reach racking tops, beams and gutters from the ground, reducing the need for access equipment. How can I clean the warehouse without disrupting operations? Schedule larger cleaning jobs for quieter periods, use ride-on machines to cover large areas quickly, and deal with spills as they happen. Can you help us choose the right machines? Yes. Our team can visit your warehouse and recommend equipment to suit your floor area, layout and cleaning routine.

Introduction A scrubber dryer is a significant investment, and for many businesses it is the machine that keeps floors safe and clean every day. When it breaks down, cleaning slows to a crawl, mops come back out and floors are left wetter and dirtier than they should be. Yet many machines are only looked at when something goes wrong.  A service contract changes that. Regular, planned servicing keeps your scrubber dryer working properly , helps it last longer and reduces the risk of a breakdown at the worst possible moment. Here is why it is worth considering. What wears out on a scrubber dryer Scrubber dryers work hard, and several parts wear with everyday use: • Brushes and pads lose their effectiveness as they wear down, so the machine cleans less well. • Squeegee blades wear and split, leaving streaks and water behind instead of a dry floor. • Batteries lose capacity over time, especially if they are not charged and maintained correctly. • Hoses, filters and seals can block, crack or leak, reducing suction and water flow. • Vacuum motors and drive systems can suffer if debris gets into the wrong places. Most of these issues develop gradually. Operators often get used to a machine that is slowly performing worse, until it stops altogether. What a planned service checks A planned service is a thorough inspection by a trained engineer. It typically includes checking and adjusting brushes, pads and squeegees, testing batteries and charging, inspecting hoses, filters and seals, checking motors, drives and electrical systems, and replacing worn parts before they fail. The engineer can also spot problems caused by how the machine is being used and give your team practical advice. The real cost of downtime When a scrubber dryer breaks down unexpectedly , the cost is not just the repair. Cleaning takes longer, staff time goes up, standards slip and, in busy environments, floors may be less safe. If you need a machine urgently, you may also face rushed decisions about repairs or replacement. A service contract turns unpredictable repair bills into a planned, budgeted cost. It also helps the machine reach its full working life, which protects your original investment. Better results from the same machine A well-maintained scrubber dryer simply cleans better. Fresh brushes, a sharp squeegee and healthy batteries mean cleaner floors, faster drying and more consistent results across every shift. For sites with standards to meet, such as food production, healthcare or retail, that consistency matters. Looking after a mixed fleet Many sites run several machines, often from different brands, such as Tennant, Viper, Numatic and i-mop . Bringing them all under one service plan makes life simpler: one point of contact, planned visits and a clear picture of the condition of every machine. Servicing from a local team Cornwall Vacuum Services has been supplying, servicing and repairing commercial cleaning equipment across Cornwall, Devon, Somerset and Dorset since 1991. Our engineers can carry out planned servicing on your scrubber dryers and other cleaning machines, and our repair centre handles faults when they happen. We can also build servicing into the purchase or lease of a new machine. Contact our team to discuss a service agreement for your equipment. FAQs How often should a scrubber dryer be serviced? It depends on how often the machine is used. Machines used daily on large sites benefit from more frequent servicing than those used occasionally. Our team can recommend a schedule. What is included in a scrubber dryer service? A service usually covers brushes, pads and squeegees, batteries and charging, hoses, filters and seals, and motors and electrical systems, with worn parts replaced as needed. Is a service contract worth it? For most businesses, yes. Planned servicing reduces the risk of breakdowns, keeps cleaning results consistent and helps the machine last longer. Can you service machines from different brands? We work with a wide range of commercial cleaning machines. Tell us the makes and models you have and we will confirm how we can help. Can servicing be included when we buy or lease a new machine? Yes. Servicing can be built into the purchase or lease of a new machine.

Supermarket floors never get a break. Customers, trolleys, staff and deliveries cross them from opening to closing, and spills happen at any time. Yet many stores still rely on mops and buckets during the day, leaving wet floors, warning signs and a slip risk in busy aisles. Slips and trips are the most common cause of major injury in UK workplaces, according to the Health and Safety Executive , and a wet floor in a busy shop is a risk for customers and staff alike.  So how can supermarkets keep floors clean during trading hours without creating a hazard? Why mops are a problem in busy stores A mop spreads water across the floor and leaves it to dry on its own. In a busy store, that means areas that stay wet while customers walk through them. Mops also tend to move dirt around rather than remove it, and the water in the bucket quickly becomes dirty. The result is a floor that looks streaky and takes longer to dry. How scrubber dryers help A scrubber dryer washes the floor and removes the dirty water in a single pass. The squeegee and vacuum lift the water straight away, so the floor is left clean and dry rather than wet. That means: • less time with wet floors in customer areas • a lower slip risk than mopping • a more consistent clean across the whole store • less physical effort for cleaning staff Because modern battery-powered scrubber dryers are quiet and compact, many can be used while the store is open. Choosing the right size of machine The right machine depends on the size and layout of your store: • Convenience stores and small supermarkets: compact machines such as the i-mop XXL Pro or the Tennant T260 work well in narrow aisles and around displays. • Mid-sized supermarkets : walk-behind machines such as the Tennant T360 or Viper AS5160T cover more ground while staying manoeuvrable. • Large superstores: ride-on machines such as the Tennant T7, or a compact ride-on such as the Viper AS530R, clean wide aisles and large open areas quickly. Many larger stores use a ride-on machine overnight and a compact machine during the day for spills and touch-ups. Daytime and overnight cleaning For most stores, the main floor clean happens before opening or after closing, when aisles are clear. During the day, the focus moves to spills, entrances and high-traffic areas. A compact, quiet scrubber dryer is ideal for this, as staff can deal with a spill quickly and leave the area dry rather than coning it off. Clear signage is still important whenever cleaning takes place, but a dry floor in one pass reduces the time any area is out of action. Back of house, entrances and outside The shop floor is only part of the picture. Warehouses, loading bays and stock rooms collect dust, packaging debris and tyre marks from pallet trucks, so a sweeper or scrubber dryer helps keep these areas safe too. Entrances, trolley bays and forecourts can be cleaned with a pressure washer and a flat surface cleaner such as the Turbo Devil TD520 , which cleans large paved areas evenly and quickly. Support across multiple stores If you manage several stores, planned servicing across all your machines helps keep them reliable and avoids breakdowns at busy times. Leasing can also make it easier to equip several sites at once. Cornwall Vacuum Services supplies, leases, services and repairs scrubber dryers for retailers across Cornwall, Devon, Somerset and Dorset. We can visit your store, look at your floors and cleaning routine, and recommend the right machine. Contact our team to arrange a consultation. FAQs Can a scrubber dryer be used while customers are in the store? Many compact, battery-powered scrubber dryers are quiet enough for daytime use. Because they leave the floor dry, they reduce the slip risk compared with mopping. What size scrubber dryer does a supermarket need? It depends on the store size and aisle widths. Small stores suit compact machines, while large superstores benefit from ride-on models. Are scrubber dryers better than mops? For most supermarket floors, yes. They clean more consistently and leave the floor dry, which is safer for customers and staff. What is the best way to clean store entrances and trolley bays? We supply pressure washers and flat surface cleaners that make cleaning entrances, trolley bays and forecourts much quicker. Do you offer servicing for multiple stores? Yes. We can arrange planned servicing for machines across several sites.

Supermarket floors never get a break. Customers, trolleys, staff and deliveries cross them from opening to closing, and spills happen at any time. Yet many stores still rely on mops and buckets during the day, leaving wet floors, warning signs and a slip risk in busy aisles. Slips and trips are the most common cause of major injury in UK workplaces, according to the Health and Safety Executive , and a wet floor in a busy shop is a risk for customers and staff alike.  So how can supermarkets keep floors clean during trading hours without creating a hazard? Why mops are a problem in busy stores A mop spreads water across the floor and leaves it to dry on its own. In a busy store, that means areas that stay wet while customers walk through them. Mops also tend to move dirt around rather than remove it, and the water in the bucket quickly becomes dirty. The result is a floor that looks streaky and takes longer to dry. How scrubber dryers help A scrubber dryer washes the floor and removes the dirty water in a single pass. The squeegee and vacuum lift the water straight away, so the floor is left clean and dry rather than wet. That means: • less time with wet floors in customer areas • a lower slip risk than mopping • a more consistent clean across the whole store • less physical effort for cleaning staff Because modern battery-powered scrubber dryers are quiet and compact, many can be used while the store is open. Choosing the right size of machine The right machine depends on the size and layout of your store: • Convenience stores and small supermarkets: compact machines such as the i-mop XXL Pro or the Tennant T260 work well in narrow aisles and around displays. • Mid-sized supermarkets : walk-behind machines such as the Tennant T360 or Viper AS5160T cover more ground while staying manoeuvrable. • Large superstores: ride-on machines such as the Tennant T7, or a compact ride-on such as the Viper AS530R, clean wide aisles and large open areas quickly. Many larger stores use a ride-on machine overnight and a compact machine during the day for spills and touch-ups. Daytime and overnight cleaning For most stores, the main floor clean happens before opening or after closing, when aisles are clear. During the day, the focus moves to spills, entrances and high-traffic areas. A compact, quiet scrubber dryer is ideal for this, as staff can deal with a spill quickly and leave the area dry rather than coning it off. Clear signage is still important whenever cleaning takes place, but a dry floor in one pass reduces the time any area is out of action. Back of house, entrances and outside The shop floor is only part of the picture. Warehouses, loading bays and stock rooms collect dust, packaging debris and tyre marks from pallet trucks, so a sweeper or scrubber dryer helps keep these areas safe too. Entrances, trolley bays and forecourts can be cleaned with a pressure washer and a flat surface cleaner such as the Turbo Devil TD520 , which cleans large paved areas evenly and quickly. Support across multiple stores If you manage several stores, planned servicing across all your machines helps keep them reliable and avoids breakdowns at busy times. Leasing can also make it easier to equip several sites at once. Cornwall Vacuum Services supplies, leases, services and repairs scrubber dryers for retailers across Cornwall, Devon, Somerset and Dorset. We can visit your store, look at your floors and cleaning routine, and recommend the right machine. Contact our team to arrange a consultation. FAQs Can a scrubber dryer be used while customers are in the store? Many compact, battery-powered scrubber dryers are quiet enough for daytime use. Because they leave the floor dry, they reduce the slip risk compared with mopping. What size scrubber dryer does a supermarket need? It depends on the store size and aisle widths. Small stores suit compact machines, while large superstores benefit from ride-on models. Are scrubber dryers better than mops? For most supermarket floors, yes. They clean more consistently and leave the floor dry, which is safer for customers and staff. What is the best way to clean store entrances and trolley bays? We supply pressure washers and flat surface cleaners that make cleaning entrances, trolley bays and forecourts much quicker. Do you offer servicing for multiple stores? Yes. We can arrange planned servicing for machines across several sites.

Introduction A golf course depends on its machinery. Mowers, buggies, utility vehicles and turf equipment work hard every day, and the end of every shift brings the same job: washing off grass, mud and grease before the next day's work. How well that is done affects how long your machinery lasts, how reliably it runs and how much time your greenkeeping team spends on maintenance. This guide covers what course managers and head greenkeepers need to know about machinery washdown, from choosing a pressure washer to setting up a practical wash area. Why clean machinery lasts longer Wet grass clippings and soil hold moisture against metal parts, which encourages rust and corrosion . Grease and dirt build up around moving parts, hide wear and damage, and make routine checks harder. Clean machinery is easier to inspect , easier to service and less likely to break down in the middle of the season. A consistent washdown routine also helps your machinery present well on the course, which members and visitors notice. Hot or cold water? Cold water pressure washers are effective at r emoving fresh grass and loose soil, and they are simple and economical to run. Hot water pressure washers go further, cutting through grease, oil and dried-on dirt much more quickly. If your team regularly deals with greasy machinery or stubborn build-up, hot water can save a lot of time. CVS supplies both types, including: • Dirt Driver Sapphire 1500 and 2200: diesel-heated hot water pressure washers for heavy-duty cleaning • Dirt Driver Electrifire range: all-electric hot water machines with no exhaust fumes, suited to covered or indoor wash areas • Evolution 1 and Evolution 2 : petrol cold water pressure washers that work without mains power, ideal for remote parts of the course Protecting bearings and electrics Pressure washing is powerful, so technique matters . Spraying high-pressure water directly at bearings, seals, electrical connections and engine components can force water and dirt into places it should not go. Train staff to keep a sensible distance, use a wider spray angle around sensitive parts and let machinery cool before washing. Many greenkeeping teams blow off loose clippings first, then use the pressure washer for the remaining dirt and grease. This reduces the amount of water used and the debris washed into the wash area. Setting up a practical wash area A dedicated wash area makes washdown faster, safer and easier to manage. Think about: • Location: close to the machinery store, with enough space to move mowers and vehicles around. • Surface : a hard, well-drained surface that is easy to clean. • Equipment: a fixed or mobile pressure washer within easy reach, with hoses long enough to get around larger machines. • Security: a static, tamper-proof washer can be a good choice where several staff share the wash area. Clippings and soil should be cleared regularly so they do not build up or block drains. Keeping wash water out of surface water drains Machinery wash water contains grass, soil, oil and grease, so it should not run into surface water drains or watercourses. Many courses use grass traps, interceptors or water treatment and recycling systems to manage run-off. Guidance varies, so check the current requirements from your environmental regulator when planning or upgrading a wash area. Fixed or mobile pressure washers? A fixed or static unit suits a dedicated wash bay and is always ready to use. A mobile pressure washer can be moved around the maintenance yard or taken out on the course. Petrol models are especially useful where there is no mains power. Many courses use a fixed machine for daily washdown and a mobile one for jobs elsewhere. Beyond the maintenance yard The same equipment can help around the rest of the club. Flat surface cleaners such as the Turbo Devil TD520 attach to a pressure washer and clean paths, patios and terraces evenly. For clubhouse gutters, a high-level vacuum such as the skyVac Industrial 85 clears gutters from the ground without scaffolding. Support through the season Cornwall Vacuum Services supplies, services and repairs pressure washers for golf courses across Cornwall, Devon , Somerset and Dorset. We can recommend the right machine for your wash area, offer leasing to spread the cost , and service your equipment before the season starts so it is ready when you need it. Contact our team to discuss your requirements. FAQs What is the best pressure washer for golf course machinery? It depends on your workload. Hot water machines such as the Dirt Driver Sapphire range are best for grease and heavy dirt, while petrol cold water machines such as the Evolution range suit areas without mains power. Is hot water necessary for washing mowers? Not always. Cold water handles fresh grass and soil well, but hot water is much quicker at removing grease and dried-on dirt. Can pressure washing damage golf machinery? It can if water is sprayed directly at bearings, seals or electrics. Good technique and a sensible spray distance avoid this. Do I need a dedicated wash bay? A dedicated area makes washdown faster and helps you manage run-off properly, but the right set-up depends on your course and budget. Can you service our pressure washers before the season? Yes. Our engineers carry out servicing and repairs to help keep your equipment reliable through the busy months

Introduction When a warehouse or factory floor gets too big to clean by hand, the next step is a machine. Two types come up again and again: floor sweepers and scrubber dryers. They look similar and are often mentioned together, but they do very different jobs. Choosing the wrong one can leave you with a machine that does not solve your problem. So which do you need, a sweeper, a scrubber dryer, or both? This guide explains the difference and how to decide. What a sweeper does A floor sweeper is designed to pick up loose dirt and debris. Rotating brushes flick dust, grit, packaging, wood splinters, swarf and litter into a hopper, while a filter system helps control the dust. Sweepers work on dry floors and are ideal for clearing large areas quickly. Options include the IPC 464, 512 and 750E sweepers and ride-on machines such as the Tennant S20 , which can cover warehouse floors, yards, car parks and site roads. What a scrubber dryer does A scrubber dryer cleans the floor itself. It applies water and cleaning solution, scrubs the surface with brushes or pads, then lifts the dirty water away with a squeegee and vacuum. It removes ingrained dirt, oil, spills and tyre marks that a sweeper cannot shift, and leaves the floor dry and safe to walk on. For large industrial floors, ride-on scrubber dryers such as the Tennant T20 and Tennant T7 cover big areas quickly and keep operators comfortable through long cleaning sessions. The key difference The simplest way to think about it is this: • A sweeper removes loose debris. • A scrubber dryer removes dirt that is stuck to the floor. If your problem is dust, grit and packaging waste, a sweeper is the right starting point. If your floor looks grimy, has tyre marks or oily patches, or needs to meet a higher standard of hygiene, you need a scrubber dryer. Why many large sites use both On busy industrial sites, the best results usually come from sweeping first and scrubbing second . Sweeping clears loose debris that would otherwise clog the scrubber dryer's squeegee and filters, or simply be pushed around in dirty water. The scrubber dryer then has a cleaner surface to work on, so it cleans more effectively and needs less maintenance. A common routine is to sweep daily to control dust and debris, and scrub traffic lanes and production areas as often as they need it. Indoor and outdoor areas Sweepers are not just for indoor floors. Many are suited to loading bays, yards, car parks and access roads, where debris builds up quickly and a scrubber dryer would not be practical. If your site has large outdoor areas as well as a warehouse floor, a sweeper can cover both. Scrubber dryers are mainly used indoors on hard floors such as sealed concrete, resin and vinyl. What about combination machines? Some larger machines combine sweeping and scrubbing in one. These can be a good choice for very large sites that want a single machine and operator, but they are a bigger investment. For many warehouses and factories, a separate sweeper and scrubber dryer offers more flexibility , as each machine can be used where and when it is needed. How to decide Ask yourself a few questions: • What does the dirt on your floor look like: loose debris, or ingrained marks and spills? • How large is the area, and does it include outdoor space? • How often does the floor need cleaning, and how much time is available? • Do you need to meet hygiene standards for food or production? Your answers will usually point clearly towards a sweeper, a scrubber dryer, or both. Advice from a local team Cornwall Vacuum Services supplies, services and repairs industrial sweepers and scrubber dryers across Cornwall, Devon, Somerset and Dorset. We can look at your site, the type of dirt you deal with and your cleaning routine, then recommend the right machine or combination of machines. Contact us to arrange a site visit. FAQs What is the difference between a sweeper and a scrubber dryer? A sweeper picks up loose dust and debris from dry floors. A scrubber dryer washes and scrubs the floor, then dries it, removing ingrained dirt, spills and marks. Do I need a sweeper if I have a scrubber dryer? On sites with a lot of loose debris, yes. Sweeping first protects the scrubber dryer and helps it clean more effectively. Can a sweeper be used outside? Many sweepers are suitable for yards, loading bays and car parks as well as indoor floors. Check the model's intended use before buying. Which is better for a factory floor? Most factories benefit from both: a sweeper for debris such as swarf and packaging, and a scrubber dryer for oil, spills and process residue. Can you help us choose? Yes. Our team can visit your site and recommend the right machine for your floor, debris and cleaning routine.

Introduction Black tyre marks are one of the most common complaints in warehouses and factories. They build up along forklift routes, around loading bays and at turning points, and they can make an otherwise clean building look tired and neglected. Mops and general cleaning rarely shift them, which leaves many site managers asking: how do you actually get rid of forklift tyre marks, and how do you stop them coming back? The good news is that most tyre marks can be removed with the right machine, the right brush or pad and the right cleaning solution. This guide explains how. Why tyre marks build up Forklifts and pallet trucks repeat the same routes many times a day. Each time a tyre turns, brakes or accelerates, it leaves a thin layer of rubber on the floor. Dust and grime stick to that layer, and over time the marks darken and spread into wide bands along aisles and turning areas. Mops tend to move this residue around rather than lift it. They can also leave a damp film that attracts more dirt. To remove the marks properly, the floor needs mechanical scrubbing and the dirty water needs to be taken away, not left behind. Use a scrubber dryer, not a mop A scrubber dryer combines scrubbing brushes or pads with a squeegee and vacuum. It loosens the rubber and grime, then lifts the dirty water off the floor in the same pass. The result is a floor that is clean, dry and safe to walk or drive on straight away. For larger warehouses and factories, ride-on machines such as the Tennant T20 , Tennant T981 and Viper AS1050R can cover traffic lanes and loading areas quickly. For smaller sites, a walk-behind scrubber dryer can do the same job on a smaller scale. Daily cleaning vs periodic deep cleans The easiest way to deal with tyre marks is to stop them building up in the first place. Regular scrubbing of the busiest routes, daily or several times a week depending on traffic, removes fresh marks before they set in. Where marks have been left to build up for months, a deeper clean is usually needed first. This may involve slower passes, a more aggressive pad or brush and a stronger cleaning solution. Once the floor is back to a good standard, a regular routine keeps it that way with far less effort. Choosing the right brush or pad The brush or pad makes a big difference to the result. Softer pads suit routine cleaning of sealed or coated floors , while firmer brushes and more abrasive pads are used for heavier build-up on bare concrete . Using a pad that is too aggressive on a coated floor can damage the finish, so it is important to match the brush or pad to your floor type. If you are not sure what your floor is or which brush to use, our team can advise before you start. Choosing a cleaning solution Water alone will not remove rubber residue. A suitable floor cleaning chemical, such as a heavy-duty hard floor cleaner from the Prochem range, helps break down the marks so the machine can lift them. Always check that the product is suitable for your floor type and follow the dilution instructions , as using too much chemical can leave a sticky residue that attracts more dirt. Preventing tyre marks coming back A few simple steps help keep floors looking better for longer: • Scrub the busiest traffic lanes and turning areas most often. • Sweep regularly so grit and dust do not grind into the floor. • Clean spills quickly before vehicles spread them. • Keep forklift tyres in good condition. • Service your scrubber dryer regularly so brushes, squeegees and pads stay effective. Expert advice for your floor Cornwall Vacuum Services has supplied and serviced commercial cleaning equipment across Cornwall, Devon, Somerset and Dorset since 1991. Whether you need a new scrubber dryer, the right brushes and pads for your existing machine, or advice on tackling stubborn marks, our team can help. Contact us to arrange a consultation. FAQs What is the best way to remove forklift tyre marks? A scrubber dryer with the right brush or pad and a suitable cleaning solution is the most effective method. It scrubs the marks loose and removes the dirty water in a single pass. Can I remove tyre marks with a mop? Mops usually spread the residue rather than remove it, especially on heavily marked floors. Machine scrubbing gives a much better result. How often should warehouse floors be scrubbed? It depends on traffic levels. Busy routes and turning areas may need scrubbing daily, while quieter areas can be cleaned less often. Will scrubbing damage my floor? Not if the brush, pad and chemical are matched to your floor type. Overly abrasive pads can damage coated floors, so check before you start. Can you help us choose the right brushes and pads? Yes. Our team can recommend brushes, pads and cleaning solutions to suit your floor and your machine.